- 您现在的位置：买卖IC网 > Sheet目录527 > SX1231-31SKB915 (Semtech)TVS
SX1231
WIRELESS & SENSING PRODUCTS
DATASHEET
3. Chip Description
This section describes in depth the architecture of the SX1231 low-power, highly integrated transceiver.
3.1. Power Supply Strategy
The SX1231 employs an advanced power supply scheme, which provides stable operating characteristics over the full
temperature and voltage range of operation. This includes the full output power of +17dBm which is maintained from 1.8 to
3.6 V.
The SX1231 can be powered from any low-noise voltage source via pins VBAT1 and VBAT2. Decoupling capacitors should
be connected, as suggested in the reference design, on VR_PA, VR_DIG and VR_ANA pins to ensure a correct operation
of the built-in voltage regulators.
3.2. Low Battery Detector
A low battery detector is also included allowing the generation of an interrupt signal in response to passing a
programmable threshold adjustable through the register RegLowBat . The interrupt signal can be mapped to any of the DIO
pins, through the programmation of RegDioMapping .
3.3. Frequency Synthesis
The LO generation on the SX1231 is based on a state-of-the-art fractional-N PLL. The PLL is fully integrated with
automatic calibration.
3.3.1. Reference Oscillator
The crystal oscillator is the main timing reference of the SX1231. It is used as a reference for the frequency synthesizer
and as a clock for the digital processing.
The XO startup time, TS_OSC, depends on the actual XTAL being connected on pins XTA and XTB. When using the built-
in sequencer, the SX1231 optimizes the startup time and automatically triggers the PLL when the XO signal is stable. To
manually control the startup time, the user should either wait for TS_OSC max, or monitor the signal CLKOUT which will
only be made available on the output buffer when a stable XO oscillation is achieved.
An external clock can be used to replace the crystal oscillator, for instance a tight tolerance TCXO. To do so, bit 4 at
address 0x59 should be set to 1, and the external clock has to be provided on XTA (pin 4). XTB (pin 5) should be left open.
The peak-peak amplitude of the input signal must never exceed 1.8 V. Please consult your TCXO supplier for an
appropriate value of decoupling capacitor, C D .
XTA
XTB
NC
TCXO
32 MHz
OP
Vcc
Vcc
GND
C D
Figure 4. TCXO Connection
Rev. 7 - June 2013
Page 18
www.semtech.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SX1240SKA433
TVS
SX1701BI085TRT
IC AMP 2.5GHZ 5.3V 16-MLPQ
TA002-10002
LED HEATSINK W/FAN 12V 40X10MM
TC620HEPA
IC TEMP SNSR 5V DUAL TRIP 8-DIP
TC623CVOA713
IC TEMP SNSR 3V DUAL TRIP 8-SOIC
TC624VOA
IC TEMP SNSR PROG 2.7V 8SOIC
TC6501P125VCTTRG
IC TEMP SWTCH OPEN DRAIN SOT23A5
TCS3104FN
IC COLOR SENSOR LIGHT-VOLT 4-DFN
相关代理商/技术参数
SX1231H
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Low Power Integrated UHF Transceiver with On-Chip 20dBm PA
SX1231HIMLTRT
制造商:SEMTECH 功能描述:290MHz- 1GHz RF Transceiver
SX1231IMLTRT
制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:RF Transceiver FSK/GFSK/GMSK/MSK/OOK 3.3V 24-Pin QFN EP T/R 制造商:Semtech Corporation 功能描述:IC 433/868/915MHZ TXRX 24-QFN 制造商:Semtech Corporation 功能描述:SX Series 290 to 1020 MHz 300 Kbps Low Power Integrated UHF Transceiver - QFN-24 制造商:Semtech Corporation 功能描述:GPSS WL SKU APP1, Frequency Min:433MHz, Frequency Max:915MHz, Modulation Type:FS 制造商:Semtech Corporation 功能描述:290MHz- 1GHz RF Transceiver
SX1231ITSTRT
制造商:Semtech Corporation 功能描述:LOW-POWER INTG UHF TRANSCEIVER
SX1231J
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Low Power Integrated UHF Transceiver with On-Chip 20dBm PA
SX1231JIMLTRT
制造商:Semtech Corporation 功能描述:UHF TRANSCEIVER FOR ARIB
SX1231SKB433
制造商:Semtech Corporation 功能描述:
SX1231SKB915
制造商:Semtech Corporation 功能描述:USB KIT - SX1231 915MHZ 制造商:Semtech Corporation 功能描述:development kit